Automation Equipment Manufacturer
Advice Line:+86 13424724129

What else should be paid attention to when the liquid filling machine works stably?

Release Date:2023-04-27 11:55:44 Popularity:

  At present, the scope of use of liquid filling machines on the market is becoming wider and wider, and the problems encountered in the use of equipment are becoming more and more acute. Therefore, for the better production of enterprises, it is still very necessary to carry out related maintenance of.

What else should be paid attention to when the liquid filling machine works stably?

  First of all, before using the filling machine, bottle brushing machine and bottle rinsing machine, they should be installed and then debugged. Before debugging, they should read the instructions carefully and prepare the tools used.

  After the filling machine, bottle brushing machine and bottle rinsing machine are installed, the filling track and the bottle receiving tray are adjusted to be horizontal, the liquid storage tank is filled with materials, and all electrical switches are in the off position.

  Insert the filled container into the tooling box and connect to the external power supply. The power socket must be a three-pin socket with a reliable grounding wire to prevent people from being shocked by electric leakage from the casing. Turn the power switch of the machine to ON and the power indicator light will be on.

  The supporting plate of the loading frame supports the filling frame, and pushes the positioning sleeve on the filling head upward with your fingers. The positioning sleeve should be able to move up and down flexibly, and the filling needle in it should be exposed or retracted without hindrance.

  Turn the switch under the liquid storage tank to the open position so that the material can flow into the total metering pump. According to the total amount of container filling each time, adjust the screw on the crank and turn the knob of the filling speed control board to about 20 degrees. Then turn the switch on the filling speed control board to the open position.

What else should be paid attention to when the liquid filling machine works stably?

  When the outflow of liquid from the filling head reaches the set volume, tighten the liquid volume fine-tuning nut, cover the shell of the filling head, and loosen the support plate of the filling frame.

  In addition to the maintenance and maintenance of the liquid filling machine, it is also necessary to keep the filling workshop clean and tidy. Because a very taboo point in the production process is that the production line cannot run normally due to the quality problems of the filling machine itself, so when using the filling machine, it is necessary to pay attention to sterilization, ensure cleanliness, and low-temperature filling.

  The main methods to ensure cleanliness are: keep the pipes of the liquid filling machine clean, all pipes, especially those in direct or indirect contact with materials, and the material tanks must be brushed and sterilized to ensure that there are no parts in contact with materials. Dirt and bacteria.

  Before the filling machine works each time, use 0-1°C water to lower the temperature of the filling machine tank and the conveying pipeline. When the filling temperature exceeds 4°C, the temperature should be lowered first before filling operation, so that the materials Keep a certain constant temperature within the specified time of filling, so as not to cause the filling machine to work unstable due to excessive temperature changes.

  The filling equipment should be isolated from other equipment. The lubricating part of the filling machine and the filling material part should prevent cross-contamination. The conveyor belt should be lubricated with special soapy water or lubricating oil.

  According to the industry, before cleaning the liquid filling machine, the remaining product in the container should be cleaned up, and then the barrel should be filled with a mild cleaning solution. The cylinder has been lubricated before leaving the factory. Please do not open or add any lubricating oil to ensure that the surface of the filling machine is clean and hygienic. When it is not working, it should be powered off.

What else should be paid attention to when the liquid filling machine works stably?

  In addition, while insisting on maintenance, correct use, and regular cleaning of the filling machine, it is also necessary to carry out regular testing and debugging. Only in this way can we ensure the healthy and stable work of the liquid filling machine and bring better efficiency to the filling production of the enterprise.


Multifunctional automatic blister packaging machine for biol
Life science biological laboratory consumables pipette autom
Life science biomedical laboratory consumable pipette tip au

Online Message